EPX10000 Long Range Underground Diamond Metal Detector Gold Treasure Hunter 2018

Description

2018 New
Kit  EPX10000 Long Range Underground Metal Detector with degausser Eliminate  interference signals
1.Detection depth range:5-50m
2. Detection distance range :100-1000m
3.Rechargeable battery:8 hours of continuous work
4.Voltage:12VDC
5.The temperature range:45℃ to 85℃
6.Humidity:0~95%(non condensing)
7.16 bit processor speed,40MIPS –16MHz
8.32 bit DSS synthesis chip,wave from output
9.Digital frequency synthesisX20PLL,automatic frequency stabilizer,0.1MHz
10.Color LCD display,a resolution of 480 x 320 pixels
11.Net weight:6.6kg,Gross weight:10.5kg
12.Product size:47X37X13.5cm
1) Radar Scans LED Panel (2) Signal transmission (3) Select the metal type
Depth adjustment (5) Range adjustment (6) Receiving antenna
Scanner control installation
Note: Before the daily operation, the battery must be fully charged! If you  do not charge it, the EPX10000 might go wrong. If abnormal , this may be the  first time warning that the battery power is too low and must be charged. If  the battery power is charged a whole night, after that, the battery is still  no power, you need to replace the battery or charger, or AC power outlet  without electricity. If the battery is charged,but it is not full of  power,you may need to replace the built-in battery. A new fully charged  battery can let EPX10000 continue to work about eight hours.
Before turning on the scanner, put the EPX10000 transmitter on the ground,  the sensor antenna is connected to the corresponding jacks of the  transmitter. When open the transmitter,never plug the sensor, if doing it,  it will cause damage to the machine.
Previously used EPX10000 scan,first make all the necessary connections.
1.The sensor is connected to the scanner testing (+) testing (-) on the  jack, insert the probe of sensor on the earth
2.The transmit antenna signal transmission is mounted on the corresponding  interface
3. with the power key is turned "On / Off” knob, turn on the power. At this  time, in the LCD area, power indicator,horizontal trmming,longitudinal  trmming indicator lights.
4. at this time, EPX10000 is scanning all selected element . Before starting  the detection process, please let it work 3-5 minutes, which will be briefly  explained later.
5.after the end of the operation, remember to turn off EPX10000. For ease to  use,the instrument requires the use of a smll battery charger is connected  to the power line charg instrument.
Receiver - The rotary switch on the top of the receiver panel are the  headphone and the antenna jack. When do not use, do not connect the antenna  rods with the receiver! If the antenna rod is saved with it inserted in the  receiver , it will cause the battery to drain.
Receiving antenna rod - rod antenna is designed to point out to the operator  that he / she has entered a power transmission line between the sensor and  the target. Under normal circumstances, the operator should hand held the  antenna rod stably and balanced, as high as your waist, and slightly in  front of the operator. When hand held the antenna rods, rod antenna should  is pointed to the front and parallel to each other and separated by 8-18  inches away. Everyone needs to find their own best distance. It takes trial  and error to find. Please remember, the people who operate this device, calm  relaxed person will do better than the tense stiff! When you enter the RF  energy line, measured metal,the antenna rod will naturally cross.
And the radar scan pointer will stop in one location. When the antenna and  radar cross and the scanner pause, you see the dawn of victory would come.
The key point is that how to hold the molecular frequency detector receiver  rods , as well as body position and walk.
Users must stand in a relaxed posture, feet slightly apart, arms close to  the body but not too tight. When holding the receiver rod , the palms and  wrists should not be too hard to make it in the hands automatically reach  balance, and always parallel to each other. When hand holding the rod, let  it be parallel with the ground, in order to increase their sensitivity, or  slightly down incline 5-8 °, achieve a better balance (if you are a novice  of molecular frequency detector).
The most important thing is the way to practice holding the rod, the rod  until the two are no longer mutually "away."
After the balance of the receiver rods is completed, the operator should  learn how to walk, step by step, while maintaining a balance of two rods.  This is another trial and error: the pace must be maintained at normal  speed, firm and uniform. Each step across the same distance, otherwise the  two will be out of balance. Shrugging will lead two out of balance.  Shoulders should be maintained at the same height.
Try to practice and keep these conditions.
The holding of receiving rod, posture and walking exercises should follow  the requirements of the target test, the operator should test the target  object on the ground to observe the reaction of the receiving rod.
Once the "Scan Start " message appears on the screen, beginning at a  distance of 3 meters at EPX10000 detector loop around, keep the receiving  rod be in balance and insert the power module.
If the target object exist, when we walk in the transmission line of the  target object and EPX10000 on the ground between them, two receiver antenna  will be completely crossed. At such moment,the two shots parallel distance  is 15cm. We can double-check to determine whether it is stable signal. So  that the operator needs to return to relax, moving again to the transmission  line. If the receiving rod is crossed every time, then we can track the  target signal in Example 2 in accordance with a signal trace diagram. When  the operator through the buried objects will be no crossing. The target  objects is located in the point which is between the two rods last crossing  and two rods no crossing.Metal detectors can be used to accurately position  the target object. Referring to our example, continue to practice in order  to achieve better results.
SCANMASTER Research Center spent years testing various theories, ideas and  devices, developed this EPX10000 transmission at last,it is small, powerful,  long-distance transmission through soil frequency (RF) signals.  360°comprehensive import signal emitted by the soil. It is because of the  inductive energy ,the target can be detected.
Signal emitted by the scanner power sensor into the ground. If the target is  within the range you are looking for, then the signal is absorbed by the  target. Indicator rod is inserted into the power amplifier, the receiver  circuit becomes complete. The circuit through the operator's body  capacitance and inductance components of the power module is formed. When  the operator to walk through the transmission line between the scanner and  the target, the circuit will play an active role. The RF transmission line  inductance and the circuit inductance, capacitance of the operator's is  interacted. At this time, the normal reaction is the rods attract each  other. This is actually convey information to the operator: the target is  within range of the scanner.
The scanner's range how far and how depth it is,it depends on a number of  change factors. The first foremost and the most important variable is the  target size and then the soil conditions (presence of electrolytes) and how  long the target has been underground. Another factor is the chemical changes  in the soil around the target, the factors that can enhance the scanner's  operating performance. The target is susceptible to oxidation, no matter  itself or its container object, the signal will be issued more. The factors  due to oxidation, the target of the transmission signal amplified potential  to the scanner will be greater.
There are target within the range, when your feet start into the energy  line, under normal circumstances, the antenna rods will attract each other.  Under normal circumstances, a single target,the width of energy line is 20  inches.
Once confirm the energy line, the next step is to use S-line measurement  method or a triangulation method to detect the target.
When a person want to make sure the target position in water , cliffs and  other inaccessible (eg, lakes or streams) place, the scanner is as easy as  operating it on the ground. Remember the most important thing is that the  operator must be able to enter between the target and the power sensor, so  that the antenna rods can indicate any potential targets. Obviously, you can  not take the antenna rods underwater. The best way is to speculate, as well  as from the shore or on board measuring the target by triangulation, apply  some basic knowledge of geometry.
When operating from the shore, first look inside the scanner if there is any  objective measurement range. If something there or not, the first step is  moving the scanner, which is the easiest step to operate (north, south, east  or west) on four main compass orientation in an orientation. The second  record should be 45 °angle between the first record. For example, if the  first reading at the target location due west direction, the second reading  position in the positive direction of the northwest or the positive  direction of the southwest Referring to the figure below.
Please note that due west at the position # 1 is in the west of target. The  position # 2 is located on southwest of the target. Considering this  situation, we finally have two 45 ° angles and a 90 ° angle. Thus, from the  position # 1 to position # 2 is equal to the distance between the distance  from the position of a target. As a result, you have to measure the target  using the triangulation method, now know the distance from the position # 1  to the target.
From the ship's operator, the operator, it has some interesting challenges.  The first challenge is the deck size. The operator must be able to have a  power sensor for the center is about 5'-10 'radius. Second, the probe must  be in contact with the power sensor vessel deck. To solve this problem, use  a wet towel wrapped around the probe, wet towel in contact with the deck. RF  energy along the target direction and the deck surface. Need the buoys, in  order to help detect the target by triangulation. With the rest of the  process is very similar to the first method.
EPX10000 almost no maintenance. Receiving rods is corroded by salt and water  in the environmental , it is required to use the good quality brass to clean  regularly to ensure that the appearance and performance intact.
CONCLUSION
If you are an experienced treasure hunter, you already know at this time,  EPX10000 and the traditional targeting methods are completely different.  Scanning in a given area and directions or locate possible goals, EPX10000  is very fast. EPX10000 absorbs the signal underground from the sensor to the  target . If there are multiple targets of the same element in a given  direction, the maximum target is absorbing the signal transmission. If you  remove the larger goal, you can track smaller targets.
If you search for large deposits, such as veins, let the antenna rods in the  open scanner can begin work immediately. Open the scanner, check the area  immediately. Should not wait too long, because of the smaller veins  absorption signal will start, but the absorption amount is small. If this  occurs, the short turn off the scanner in a short time(e.g., 15-30 minutes),  so that the signals disappear. Then, turn on the scanner again, immediately  it is marked through live goal line. The EPX10000 is moved to a new location  in order to detect the target by triangulation, as follows:
Remember, first,if your local soil strata with high gold content , the  transmitter is opened longer, you receive the signal line will be more.  Second, whether it is gold powder or in blocks, all gold,gold and gold  belong to different substances. Must remember that you are using the  frequency of the electromagnetic spectrum, all frequencies will be involved.  Finally, the frequency of mutual interference may occur. Therefore, it  should be noted in the actual operation.
NOTE： we don't ship the item to PO BOX address， and we only ship the item to English address, so please leave us your physical English address when you pay.